Key takeaways
- Finish levels come from the Gypsum Association’s GA-214. They run from Level 0 (no finishing) to Level 5 (a skim coat over everything).
- Level 4 suits most offices and clinics with flat or eggshell paint. Level 5 is for gloss paint, dark colors and walls where light grazes the surface.
- Pick the level with the paint and the lighting in mind, and write it into the drawings so every bidder prices the same thing.
Why finish levels exist
“Tape and finish the drywall” can mean a dozen different things. One finisher’s ready-for-paint is another’s rough. The Gypsum Association’s standard GA-214, Recommended Levels of Gypsum Board Finish, gives the industry a shared vocabulary: six levels, each one defined by how many coats go on the joints, the fasteners and the trim. When a spec names a level, everyone bidding is pricing the same amount of work.
The six levels
| Level | What’s done | Where it’s used |
|---|---|---|
| 0 | Board hung. No taping, finishing or accessories. | Temporary walls, or where the final finish hasn’t been decided. |
| 1 | Tape set in joint compound at joints and inside corners. Tool marks and ridges are acceptable. | Above ceilings, in plenums and in service areas that are generally out of sight. Often the minimum for fire-rated walls above the ceiling. |
| 2 | Tape embedded and wiped with a thin coat; one coat on fasteners and accessories. | Where water-resistant board is a base for tile, and in warehouses, storage and garages where looks don’t matter. |
| 3 | Level 2 plus one more coat on joints and corners; two coats on fasteners and accessories. | Under heavy or medium texture, or heavy-grade wallcovering. |
| 4 | Tape embedded, then two separate coats on flat joints and one on inside corners; three coats on fasteners and accessories. Sanded smooth. | Flat paint, light texture and wallcovering. Most offices, exam rooms and clinics. |
| 5 | Level 4 plus a thin skim coat over the entire surface. | Gloss, semi-gloss or enamel paint, dark colors, and anywhere with “critical lighting”: light raking along the wall from windows or wall-wash fixtures. |
Level 4 or Level 5?
This is the decision that actually costs money. Level 5 adds a full extra operation across every square foot of the wall, plus the sanding that goes with it. It is worth it when the finished wall would otherwise show the difference between the paper face of the board and the compound over the joints. That difference, called photographing or joint banding, shows up in a few predictable situations:
- Sheen. Eggshell is usually forgiving; semi-gloss and gloss are not.
- Raking light. Long corridors with ceiling lights near the wall, wall-washer fixtures, and walls beside tall windows put light across the surface at a low angle, which exaggerates every ridge.
- Dark or saturated colors, which show differences in surface texture more than light ones.
- Feature walls in lobbies and reception areas, where people look closely and often.
A sensible commercial spec usually mixes levels: Level 5 in the lobby and main corridors, Level 4 in offices and exam rooms, Level 2 in back-of-house storage, and Level 1 above the ceiling. That puts the money where people will see it.
What Texas finishers call it
On Houston job sites you will hear “tape, float, skim, sand.” Floating is the regional word for the coats of compound that follow the tape, and skimming is a thin coat over a wider area. A scope that says “tape, float, skim, sand and touch up, ready for paint,” like the scopes at our Richmond Ave project, describes a smooth finish ready for primer. If the job needs a specific GA-214 level, put the level number on the drawings too, so there is no room for interpretation.
Getting the finish you paid for
- Write the level into the specs, room by room or wall by wall, and show it on the finish schedule.
- Check under real light. Inspect finished walls with the permanent lights on, or with a work light held to the side, before paint.
- Prime properly. A good primer evens out the porosity of paper and compound. Skipping it can undo a good finish.
- Agree on a mock-up for large Level 5 areas, so the owner, the painter and the finisher agree on what “done” looks like.
Common questions
Is Level 5 the same as a skim coat?
Level 5 is Level 4 plus a thin skim coat of joint compound, or a product made for the purpose, over the entire surface. So a skim coat is the step that makes Level 5, but skimming one patch or one joint is not a Level 5 finish.
What finish level is standard for commercial work?
There’s no single default, which is why the spec should say. Level 4 is common for offices and clinics with flat or eggshell paint. Above-ceiling and service areas are often Level 1 or 2. Lobbies, long corridors and gloss paint often get Level 5.
Can paint hide a lower finish level?
Usually not. Primer and paint make joints more visible, not less, especially with sheen and light grazing the wall. That’s why the finish level should be chosen with the paint and lighting in mind.